View source for Polycom VVX300 & VVX310 Setup Instructions

Caveat: this is simply what worked for me (KJ6WEG) in Sept 2024 on the Bay Area Mesh, and should not be considered official instructions, nor necessarily the best way to do things.  

=== Resetting the phone to factory defaults ===
If you receive a VVX300/301 phone that is set up for someone's PBX, you will want to reset it to factory defaults before configuring it for the PBX on the mesh network, following the instructions below.  If your phone has already been reset, you can continue to the setup instructions below. 

Note: the reset instructions were derived from info on [https://emak.tech/support/polycom-factory-reset-without-password/ this website]. 

==== Factory Reset with the admin password ====
If you know the admin password (default: 456), then you can reset the phone more easily with the following steps: 

# Boot up the phone and then click on the Home button
# Scroll to "Settings" (gear icon) and select it. 
# Go down to "Advanced" and select it. 
# Enter the admin password (default: 456) and press the enter button.  - If the phone says "Sorry, please try again", then you have the incorrect password.  - If the phone shows just 2 options (Change User Password & Reboot Phone), then you've entered the user password (default: 123), instead of the admin password. 
# Select "Administration Settings"
# Scroll down and select "Reset to Defaults"
# Scroll down and select "Reset To Factory"
# When it asks "Are you sure?", select "Yes" and wait for the phone to reset and reboot. 

==== Factory Reset without the admin password ====
If you do not have the current admin password, you can reset the phone using a more difficult procedure: 

# Look on the back of the phone and find the MAC address (12 characters - numbers and letters). It should be on a sticker like the one shown here. Write it down on a piece of paper or take a photo of it.  [[File:Polycom vvx300 mac sticker.png|alt=Mac Address sticker|thumb|Mac Address sticker]]
# Power off the phone by unplugging the power cable (or network cable if using PoE). 
# Plug the phone back in and carefully watch it power up. 
# When you see it "Starting Application..." and an option to Cancel, press Cancel button
# Quickly press and hold down the keys: 1, 3, 5
# After holding down the correct keys, you will be prompted to "Enter password: to reset settings". 
# Enter the MAC address of the phone as the password. In order to enter the MAC address, use the keypad to type it in each character, making sure to select the correct character type for each one: numeric (1->Aa), upper case letters (A->a1), or lower case letters (a->1A). In order to enter letters, press the button with the letter on it, and press it the number of times corresponding to the position of the letter on the key.  For example, for the letter D, select upper case letters (A->a1) and press the 3 button once for "D".  Or for the letter F, select upper case letters (A->a1) and press the 3 button three times for "F" (D -> E -> F).  
# When you are done, press the "Ok" button.  If it asks you to confirm, tell it "Yes" and the phone should reset and reboot.   If you entered the password incorrectly, or it doesn't work, press Cancel and try again.  

=== Set up the phone for the BAM PBX ===
Once you have been assigned an extension on the BAM PBX, the easiest way I found to set up the phone was to connect it to the mesh network, access the web interface, and use the "Simple Setup" page.  

==== Request an extension ====

# Go to the [[Bay Area Mesh Phone Exchange|BAM PBX page]] on this wiki
# Find the "Signup Here" link and fill out the form. 
# Wait a few days or a week or so, and you should be contacted with your extension number, password, and other details. 
# If you don't hear back, check with the PBX manager listed on the BAM PBX page (currently KJ6DZB). 

==== Connect the Phone to the mesh network ====

# Connect your phone to power (wall wart or PoE).
# Connect the network port on the back of the phone to the mesh network.  This is commonly done by plugging it into one of the LAN ports on a hAP or other mesh device. 
# Go to the page on the mesh for the device it's connected to and find the IP address of the phone (it should have gotten an address via DHCP).   - On the old AREDN UI, go to Setup, and then to the "Port Forwarding, DHCP, and Services" page. - On the new AREDN UI, on the main page, click on "LAN DHCP" to bring up the list of connected devices. 
# In the list of connected devices, find the newly connected phone and note its IP address.  

==== Access the Web Interface ====

# In a new browser tab or window, enter "http://" followed by the IP address of the phone (for example: http://10.243.221.181). 
# The web interface should come up, and show you the login page, as shown here: [[File:Polycom vvx300 web login page.png|alt=Polycom vvx300 web interface login page|thumb|Polycom vvx300 web interface login page]]
# Make sure that "Admin" is selected (not "User"). 
# Enter the admin password, which after a reset should be the default "456", and click "Submit". 
# You should now be on the web interface, showing information about the phone, and several menu options along the top. 

==== Configure the Simple Setup Page. ====

# Select "Simple Setup" in the menu.  
# Expand the 6 sections in the middle of the page (click the "+" button in each black bar). 
# Under Language:
## Leave the setting on "English (internal)", or select your language of choice. 
# Under Time Synchronization: 
## For Alternate SNTP Server, select your desired NTP server (for BAM, I suggest using pool.ntp.org or north-america.pool.ntp.org).  
## For Alternate Time Zone, select your local time zone (eg: GMT -8:00 Pacific Time). 
# Under SIP Server: 
## For Address, put: "bambox.local.mesh"
## For Port, put: "5060"
# Under SIP Outbound Proxy:
## For Address, put: "bambox.local.mesh"
## For Port, put: "5060"
# Under SIP Line Identification: 
## For Display Name, put how you want your extension displayed (eg: "ORCA x5134")
## For Address, put your extension number followed by "@bambox.local.mesh", (eg: 5134@bambox.local.mesh)
## For Authentication User ID, put your extension number (eg: "5134")
## For Authentication Password, put the password provided by the PBX manager
## For Label, put how you want your extension labeled on the phone (eg: "x5134")
# Under Base Profile: 
## Leave Base Profile with "Generic" selected. 
# Once you have all the information entered, it should look like the image here, but with YOUR extension and other info.  [[File:Polycom vvx300 simple setup page.png|alt=Polycom VVX300 web interface - simple setup page|thumb|Polycom VVX300 web interface - simple setup page]]
# Click the "Save" button at the bottom of the page.  
# Your phone should now reboot and then be configured and ready to use.  
# To test your phone, try calling one of the services on the mesh (Date/Time = x5292, Echo Test = x5294), or call a friend!