San Bruno Mountain (Building 7): Difference between revisions
mNo edit summary |
|||
| Line 244: | Line 244: | ||
* Reposition airFiber link to Fish Ranch for optimal signal strength (to be honest, this seems pretty good already) |
* Reposition airFiber link to Fish Ranch for optimal signal strength (to be honest, this seems pretty good already) |
||
| − | * Add our own backup power. We're placing too much load on the provided backup power option which is impacting their ability to stay on the air. |
||
| ⚫ | |||
| − | * Add a NUC (minipc) to experiment with hosting services at a high site. |
||
=== Completed Work === |
=== Completed Work === |
||
| + | |||
| + | ===== April 2023 ===== |
||
| + | |||
| ⚫ | |||
| + | * Added a NUC11 (minipc) to experiment with service hosting. Idle power draw is ~4W. NUC runs Proxmox to allow virtualization of services. |
||
===== March 2023 ===== |
===== March 2023 ===== |
||
* Re-terminated the cable to KN6PLV-SANBRUNO-RM. Radio was replaced thinking the connector was broken, but looks like it was bad termination. Note that the cable to this radio is only single skinned rather than the double skinned burial grade we now use. |
* Re-terminated the cable to KN6PLV-SANBRUNO-RM. Radio was replaced thinking the connector was broken, but looks like it was bad termination. Note that the cable to this radio is only single skinned rather than the double skinned burial grade we now use. |
||
| + | |||
| + | == Hosted Services == |
||
| + | An on-site NUC11 running Proxmox provides locally hosted services. The platform was chosen for its low idle power consumption (4 watts) and flexibility. |
||
| + | |||
| + | === Services === |
||
| + | |||
| + | * Mesh Map |
||
== Meshtastic == |
== Meshtastic == |
||
Revision as of 20:28, 27 April 2023
Site located on San Bruno Mountain, next to Building 7, near the KTSF transmitter (map)(photos)
Nodes
KN6PLV-SANBRUNO-HAP
Radio: Mikrotik hAP AC2
Antenna: Built-in (provides onsite wifi access to mesh)
Location: Inside the HAM Shack
Altitude: 385m
Bearing: N/A
KN6PLV-SANBRUNO-RM5
Radio: Ubiquiti Rocket M5
Antenna: 120 degree sector
Location: 37.68674, -122.43525
Altitude: 387m
Bearing: 159° toward Millbrae
KN6PLV-SANBRUNO-RM5-2
Radio: Ubiquiti Rocket M5
Antenna: 90 degree sector
Location: 37.68673, -122.43532
Altitude: 392m
Bearing: 236° toward Colma
Backbone
Dish to Fish Ranch
Radio: airFiber 5XHD
Frequency: 5.99 GHz (Licensed to K6MPP)
Bandwidth: 50 MHz
Antenna: Ubiquiti RD-5G30-LW 30 dBi
Location: 37.68678, -122.43527
Altitude: 400m
Bearing: 56° toward Oakland
Dish to San Carlos
Radio: UISP LTU Rocket
Frequency: To be finalized
Bandwidth: 50 MHz
Antenna: Ubiquiti RD-5G30-LW 30 dBi
Location: 37.68678, -122.43527
Altitude: 400m
Bearing: 149° toward San Carlos
Read Only Access: mesh / aredn-back-bone
Site Details
Tower
The tower has a 4° slope on the main lower beams. The base of the tower is approximately 23 feet wide. The first horizontal beam is 8 feet from the ground. The second beam is 7 feet above the first. The supporting angled beams, running from the group, are at an angle of 37° from vertical. The ham shack is located on the south side of the tower with a slight peeked roof. The top of the roof peek is 6 feet from the second beam. The edge of the roof is approximately level with the first beam.
The beams themselves are 3.5in horizontally, 3in vertically, and 0.25in thick with a rounded edge. The double beam which forms the second horizontal beam is 1.25in thick.
Mounting
All equipment must be mounded on galvanized supports which are themselves attached to the tower using beam clamps. All current mounting brackets should be considered unusable. Mounts using "stacked" struts are no longer allowed.
Cabling
Cabling must be run with beam camps and stainless steel zip ties and cannot be directly attached to the tower. Cables run into the shack via rubber cable glands (not the plastic tube!). Cable loops are discouraged, as is excessive cable in the shack.
Power
The site provide main power (without backup) as well as 24vdc, 12vdc and -24vdc (breakers not provided) with battery backup. No solar or generator.
Configuration
Currently the site has an Mikrotik hAP AC2, two Ubiquiti Rocket M5 + 120 degree sector antennas, a Ubiquiti UISP Router, and two Ubiquiti AirFiber dish - one pointing at Fish Ranch, the other at San Carlos. All device are power either directly, or via the router, from the house 24vdc supply.
| Device | IP | Notes |
|---|---|---|
| USIP Router | DHCP | |
| airFiber 5XHD | DHCP | to Fish Ranch, Management VLAN 100 |
| UISP LTU Rocket | DHCP | to San Carlos, Management VLAN 100 |
| VLAN | Description |
|---|---|
| 1 | AREDN WAN |
| 2 | AREDN DtD |
| 10 | Swallow XLINK |
| 13 | Fish Ranch XLINK |
| 15 | San Carlos XLINK |
| 100 | AREDN LAN |
| 911 | Emergency local management |
| Port | Description | VLANs | PoE | Notes |
|---|---|---|---|---|
| 1 | KN6PLV-SANBRUNO-HAP | 2, 13, 15, (100) | Off | hAP provides DHCP address to non-AREDN devices |
| 2 | KN6PLV-SANBRUNO-RM5-2 | 2 | 24v | Nodes are not given LAN or WAN access |
| 3 | KN6PLV-SANBRUNO-RM5 | 2 | 24v | |
| 4 | KN6PLV-SanBrunoMtn | (100) | 24v | Meshtastic node |
| 5 | (aredn) | 2 | 24v | |
| 6 | (aredn) | 2 | 24v | |
| 7 | DISH-TO-FISHRANCH | 13, 100 | 24v (4-wire) | |
| 8 | DISH-TO-SANCARLOS | 10, 15, 100 | 24v (4-wire) | |
| 9 | Local management | (911) | - | SFP, 192.168.91.1 |
| Port | Description | VLANs | Notes |
|---|---|---|---|
| 1 | (1) | WAN | |
| 2 | (U) | ||
| 3 | (U) | ||
| 4 | (U) | ||
| 5 | KN6PLV-SANBRUNO-ROUTER | 2, 10, 13, 15, (U) | Provides DHCP addresses to LAN devices |
Notes
Part of the Bay Area Backbone connecting to Fish Ranch, San Carlos and Swallow.
New Mounts
New mounts have been design using a 2" galvanized pipe attached to galvanized struts using pipe clamps. The struts are in turn attached to the tower using beam camps. The design can be found here.
All our equipment is mounted on two of these new mounts.
Future Plans
- Reposition airFiber link to Fish Ranch for optimal signal strength (to be honest, this seems pretty good already)
Completed Work
April 2023
- Added separate power backup system using EdgePower 24V with a 200Ah LiFePo4 battery.
- Added a NUC11 (minipc) to experiment with service hosting. Idle power draw is ~4W. NUC runs Proxmox to allow virtualization of services.
March 2023
- Re-terminated the cable to KN6PLV-SANBRUNO-RM. Radio was replaced thinking the connector was broken, but looks like it was bad termination. Note that the cable to this radio is only single skinned rather than the double skinned burial grade we now use.
Hosted Services
An on-site NUC11 running Proxmox provides locally hosted services. The platform was chosen for its low idle power consumption (4 watts) and flexibility.
Services
- Mesh Map
Meshtastic
A Meshtastic node KN6PLV-SanBrunoMtn is mounted above the radio KN6PLV-SANBRUNO-RM5.
Coordination
The San Bruno Mountain HAM site is own and managed by Matthew Kaufman as part of the WB6ECE Repeater Group. Coordination of changes to the site (e.g. new radios) is managed on the mailing list Sbruno_shack. Unfortunately this is an invite only group with no public archives.
Commercial Neighbors
The local WISP in this area is Etheric although they use a different tower. They license (WQTV709) spectrum from 11.2 GHz to 11.7 GHz.
Contacts
Site Admin
- Steve Ligtelyn - KC6SVW - steve@tcomeng.com
- Matthew Kaufman - KA6SQG - matthew@eeph.com
Mesh Admin
- Tim Wilkinson - KN6PLV - tim@sfwem.net